Scary Videos Caught by Investigators – The 3X

On this episode, The 3X compiled a list of videos that sure to confirm that apparitions exists, and they interact with the living. Watch as the investigators record the apparitions during their investigations and at the time, they don’t realize them caught them.

5 SCARY Ghost Videos To Make You Believe They’re REAL ! [1]Originally Published on YouTube on May 17, 2021

Text captured from transcription: youtube channel, comes youtube, sls camera, want watch, watch full, full episode, visit youtube, video comes, haunted side, figure appears, comes youtube channel, want watch full, watch full episode, visit youtube channel, video comes youtube, haunted side paranormal, side paranormal investigations, also captured something, captured something interesting, full episode investigation

Disclaimer:
Apparitions Investigations may not own some content presented.

Copyright Disclaimer under section 107 of the Copyright Act of 1976, allowance is made for “fair use” for purposes such as criticism, comment, news reporting, teaching, scholarship, education, and research. Fair use is a use permitted by copyright statute that might otherwise be infringing.

All posts on this video blog are my personal opinion, and they don’t in any way reflect the opinions of my employer. All materials, posts, and advice from this site are informational, researching, and for testing purposes only. You can use them at your own responsibility. I’m not in any way responsible for any damage done by following posts, advice, tutorials, and articles from this video blog.

References

References
1 Originally Published on YouTube on May 17, 2021

Ghost Caught on Camera by The 3X

On this episode, a man is staying in a hotel room, and he is experiencing poltergeist activity on command. Then are a series of video snippets where they capture apparitions while driving on the road. An investigator is using his SLS camera and an interest entity. Another investigator appears to be investigating a water mill and did he capture orbs?

5 SCARY Ghost Videos That Have Been CAUGHT on CAMERA ! [1]Originally Published on YouTube on Apr 12, 2021

Disclaimer:
Apparitions Investigations may not own some content presented.

Copyright Disclaimer under section 107 of the Copyright Act of 1976, allowance is made for “fair use” for purposes such as criticism, comment, news reporting, teaching, scholarship, education, and research. Fair use is a use permitted by copyright statute that might otherwise be infringing.

All posts on this video blog are my personal opinion, and they don’t in any way reflect the opinions of my employer. All materials, posts, and advice from this site are informational, researching, and for testing purposes only. You can use them at your own responsibility. I’m not in any way responsible for any damage done by following posts, advice, tutorials, and articles from this video blog.

References

References
1 Originally Published on YouTube on Apr 12, 2021

SLS Camera Performance During Investigation

In this video, I describe my thoughts on the SLS camera performance during an investigation session in a reported haunting in McAllen, Texas.

SLS Camera Performance During Investigation

I on today’s video I’m in the be talking about the SLS camera captures that we had and I would like to hear your thoughts over next EVP capture is interesting as the question is asked and I believe we get a response the respondent’s only recorded in the audit device holds the house’s Alice house is sold as is your is your name at this point of our session it seems like the SLS starts to interact not sure it gets less stars striking because I moved it slightly over to the right or to the left and is the tracking but to me it seems possible that it’s an actual start detecting an operation or nominally and it affected our infrared camera which son Sam was carrying one upon not that as part at this point of the our session here we were getting some the VPs and what the where point out as far as he is a less is that the guest list on the on the with the connect sensors is only capable of tracking to people when you introduce a third person in there I think is starts tracking the person most closes to the sensor but it does not show no more than two so here you see me get into the frame and the starts tracking me and… Track of my son and then that’s what it things that have noticed with this connect sensors set up later will wireless it will’s you do you use your representative will vision is the same you have is very amazing things will will all over the world about this and him him him regularly something you do is you will this AVP was captured in the audio recorder here is the enhanced audio the will will him him him as a there have this little montage I just wanted to show you the duration how long it takes this less to show the stick figures on the fan and it’s not always the case not sure if this is a false detection but no show you better on what I see on this next sequence I’m demonstrating that my stick figure transfers from my silhouette to the fan and I’m thinking yes less is thinking that the fan is a single went in the stars track but you can nearly see my silhouette without a stick figure and I’m on anyone unseen so this is an is interesting capture you here she can see at this point it stops tracking the fan as it was a person doesn’t put the stick figures on there and we and our session that would move out for ticket for break at this time no one was inside the house when the ramp proximity sensor goes off at this point with everybody outside the building the only thing they got capture was the Rams proximity sensor going off no EVP’s or movement was otherwise captured going this time frame so these were interesting captures that we had on this particular investigation I’m curious to see if I can duplicate this at my home and possibly disprove that these are false detections I personally think that they were anomalies that the sensor was picking up but that will have to see if I can do became is not at a party point that there were anomalies thank you for watching his relief

SLS Camera Modification and Enhancements

I got an SLS camera for ghost hunting and investigations. The unit I purchased from Gotcha Ghost which uses the Kinetic Version 1.

While learning how to use it, I realized that the unit does not have much support when mounted on the tripod. The image below shows, two points here it makes contact with the tripod.

2 points of contact with the tripod mount

My concern here was that if I want to move the camera from room to room and let it run for long periods of time, I may find a failure point on the mount. The screw between the tripod and SLS mounting bracket is overly stressed. I may find my self with a failure point in tripod bracket.

SLS fully assembled (minus handle) is about 4 lbs. This includes Kinect sensors, battery pack, and a tablet.

SLS Camera fully assembled weighing at about 4 lbs

My thoughts were to increase surface contact between the SLS camera and tripods mounting bracket. This can distribute the weight of the camera and reduce the risk of the assembled product from turning.

First thoughts for prototyping, was to create a clay block to fit between SLS camera bracket mount and the tripod mounting bracket. This clay is soft to shape, and then you heat it up to harden the clay. The following images will show how this clay model looked like.

Clay mold on the SLS camera bracket
Clay mold between SLS camera and tripod brackets
Clay molds after a good one time use in an investigation … :\

After my first use in an investigation, it worked great. I did not have second thoughts on the weight distribution and weak points between the camera and tripod. The only concern I did have was that the camera and recording were leaning a bit because the clay mold did not have the same height all around.

Chicken scratch … ๐Ÿ™‚

So, I decided to create a 3D printed model for a more permanent solution.

I recorded a bunch of measurements from all of the equipment.

To build the 3D model I used freeCAD.

freeCAD 3D modeling

In the following image, after several prints and fittings, the product looks a lot better. The height is consistent, and weight distribution is great. The movement on the tripod is to minimal, and I should be able to carry this guy around during the investigation and last longer than one investigation.

If you would like the dimensions and freeCAD file for this model, please register and send me a comment or message. Not sure if the model will work with your tripod, but you can modify it for your purpose.

In the future, I am planning to create a similar modification to allow the mounting of a small full spectrum camera just above the Kinect sensors.